Pellet Stove Igniters

Pellet Stove Igniters

Having issues wth your pellet stove or wood stove igniter? We have selected a range of the finest pellet stove igniters which will give you trouble free operation. GET FREE SHIPPING OVER $99. All igniters are direct drop in and are made from the very best materials. Some are available in ceramic which are the ultimate choice. Fitting igniters is well within the capabilities of most stove owners and can be changed out using a small selection of tools.  If you require assistance please contact our friendly support and we will be happy to assist you.  

Set Descending Direction
View as Grid List

15 Items

per page
  1. Avalon and Lopi Kwik-Fire Igniter PP3550
    $24.00
  2. Breckwell Pellet Stove Igniter C-E-IGN
    $32.00
  3. Country Flame 400 Watt Pellet Stove Igniter PP-665
    $28.50
  4. Danson PelPro & Pleasant Hearth Igniter Element
    $27.00
  5. Englander Smart Stove Igniter AC-CHSS
    $37.80
  6. Enviro, Regency, VistaFlame 300W Ignitor - #50-1067-AMP
    $35.00
  7. Glow Boy & Pel Pro KS-5030-1061
    $27.00
  8. Harman Pellet Stove Exhaust Thermistor Esp Probe (Red)
    $24.99
  9. Harman Pellet Stove Igniter 3-20-677200
    $21.99
  10. Hudson River Pellet Stove Igniter HRSP 114S
    $40.50
  11. Jamestown Pellet Stove Igniter 07XAD
    $40.50
  12. Kozi Pellet Stove Igniter EC2-HA-120
    $29.99
  13. Lennox / Country Winslow Pellet Stove Ignitor H6005
    $42.00
  14. Osburn Igniter Rod 44030
    $27.00
  15. SBI Igniter Rod 120v 44132
    $34.20
Set Descending Direction
View as Grid List

15 Items

per page

Having Issues With Your Pellet Stove Igniter?

When your control board sends signals to the igniter it should automatically light your pellet stove. There are many types of igniters, but they all work similarly, with a goal to turn electricity into heat energy. Some types of pellet stove igniters preheat air within the burnpot, while others directly contact the pellets to ignite them. It's very difficult to light pellets for a pellet stove, without an igniter, so it can be very annoying when your igniter fails and you have to watch it continuously so it does not go out.

Here are some troubleshooting ideas to get your igniter going again.

Required Tools

  • Multimeter
  • Clamps
  • Testing wire 
  • Power strip with on-off switch
  • Owner’s manual

1. Is the igniter glowing/lighting up?  

If your igniter is light correctly, then it should have a strong, red glow, as red as a stoplight. However, some types of igniters are cool at the end and may to turn red all over, in this case, consult your user manual or contact the supplier if you are not sure.

If your igniter bends or has a bubble, this is a clear indicator that it should be replaced.

2. Is it receiving power?

An igniter needs between 115-120 volts of electricity to ignite and cycle on. This is where your multimeter will come in handy. Check the wire connection voltage to verify it's correct. 

Your igniter will probably require replacing if 115-120v is shown in your multimeter, but it is not getting hot. However, if there is no power going to the igniter, then this could indicate a broken connection. Consult your owners' manual and find the wiring diagram to locate the break, starting with the igniter wires and then make your way back towards the source of power to find the break.